Uncoated Stainless Steel Dental Orthodontics Pliers,Clamping Type/Bending Type/Cutting Type/Removing Type
●Used for clamping, bending, shearing and removal in orthodontic treatment
●Medical stainless steel acid and rust resistant
●No coating, use more assured
Tips: If the payment amount is more than $5000, you are advised to choose the bank for payment.
Uncoated Advantage
1.Materials:
Uncoated material selection requirements are very high, expensive medical stainless steel materials can be the basis for the production of uncoated products, to ensure its excellent corrosion resistance while having high hardness and environmental standards.
2.Process:
No coating is very demanding on the surface treatment of the product, there is no coating concealer, completely clear, so no defects, fine cracks, surface roughness and so on will be very obvious. No coating series - are generally polished by more than 10 years of experience of the master.
3.Durability:
The rust resistance of the material itself and the excellent surface treatment process make it have an unparalleled service life. The use of electroplating equipment for a long time, the surface coating off or uneven coating during processing will cause rust, and once rust is out of control. No coating corrosion resistance does not depend on the surface coating, the corrosion resistance of the substrate itself is the basis of rust prevention, so it can be as new as time.
4.Non-toxic whitening:
No coating series for environmental protection equipment, the material is made of medical stainless steel. Hexavalent chromium and cyanide in electroplating equipment are highly toxic substances and are easily absorbed by the human body.
Dental Orthodontics Pliers
Dental orthodontics pliers for dental orthodontics.Stainless steel material.A orthodontics instrument of high quality.
301/301G Pointed amphibious Pliers/Universal Pliers
Item No.: 004-301(Head not inlaid with cemented carbide)/301G(Head inlaid with cemented carbide)
Usage: It is used for bending various kinds of fine bending of different arcs of bows, and bending various spring bends. The pliers head can be inlaid with cemented carbide, and the middle belt of the pliers beak is cut off.
302/302G Fine wire bow bent Pliers
Item No.: 004-302(Head not inlaid with cemented carbide)/302G(Head inlaid with cemented carbide)
Usage: It is used to bend various kinds of fine bending of different arcs of bows, and bend various spring bends. The middle of the beak of the pliers is designed with a hard and sharp cutting edge, which can conveniently cut off the excess wire ends.
303/303G Cut off at the end(tipped) Pliers
Item No.: 004-303(Head not inlaid with cemented carbide)/303G(Head inlaid with cemented carbide)
Usage: It is used to cut off the end of too long bow wire, and can clip the cut and tie the top, the cut and tie the mouth is less than 0.5mm, and the edge can be inlaid with cemented carbide.
304/304G Filaments cut off(tipped) Pliers
Item No.: 004-304(Head not inlaid with cemented carbide)/304G(Head inlaid with cemented carbide)
Usage: Used to cut the diameter of 0.3mm less than the ligature wire, rubber ring, etc., the cutting edge can be inset with carbide (can not be used to cut the main bow wire).
305 Heavy Wire Cutter Pliers
Item No.: 004-305
Usage: Heavy wire cutter pliers ,for cutting heavy ligature wires up to 0.9mm
306/306G Semilunar trapezoid(tipped) Pliers
Item No.: 004-306(Head not inlaid with cemented carbide)/306G(Head inlaid with cemented carbide)
Usage: Bend the bow wire, clamp the free groove, orthodontic material, remove the back teeth, clamp the middle band of the beak, remove the attachment.
307/307G Torque formation(tipped) Pliers
Item No.: 004-307(Head not inlaid with cemented carbide)/307G(Head inlaid with cemented carbide)
Usage: Used for wire bending to form a square wire bow torch, often used in pairs, the size of the bending bow should generally not exceed 0.56x0.71mm.
308/308G Kim(tipped) Pliers
Item No.: 004-308(Head not inlaid with cemented carbide)/308G(Head inlaid with cemented carbide)
Usage: For bending multiple square wire bows with mid-beak band cut, up to 0.021x0.025 inches.
309 Force Module Separator
Item No.: 004-309
Usage: 1)Reverse action handles and long tapered tips make placing separating modules quick and easy.
2)Designed for easy placement of separating elastics. Modules will not slip because of the undercut of the tips.
310S/310SG How plier straight(tipped) Pliers
Item No.: 004-310S(Head not inlaid with cemented carbide)/310SG(Head inlaid with cemented carbide)
Usage: It is used for inserting the bow wire into the buccal canal, ligating the bow wire or forming the anterior tooth band. With the circular mesh tooth area clamping, the wire can be easily and stably bent to any Angle without easily damaging the wound tissue.
310C/310CG How plier curved(tipped) Pliers
Item No.: 004-310C(Head not inlaid with cemented carbide)/310CG(Head inlaid with cemented carbide)
Usage: It is used for inserting the bow wire into the buccal canal, ligating the bow wire or forming the anterior tooth band. With the circular mesh tooth area clamping, the wire can be easily and stably bent to any Angle without easily damaging the wound tissue.
311 End bending Pliers
Item No.: 004-311
Usage: It is mainly used for the end bending of bow wire, especially NiTi wire. The NiTi wire is bent without heating and can be bent with a diameter of 0.021 ".
312 Vertical bending(tipped) Pliers
Item No.: 004-312
Usage: The dimensions of the vertical steps for bending the various heights on the orthotic bow wire are 3mm, 4mm, 5mm and 6mm, and the diameter of the bending wire is generally not more than 0.6mm.
313S Bracket removal straight Pliers
Item No.: 004-313S
Usage: Bracket remover pliers(straight),For easy incisal-gingival (vertical) use or ,if needed,for mesial-distal (horizontal) use with the same ease.
313CH Bracket removal Pliers(Curved 45°)
Item No.: 004-313CH
Usage: Bracket remover pliers(curved 45°),For removing all bonded attachment .May be used mesial-distal (horizontal) or incisal-gingival (vertical) in anterior areas.Angled perfectly for easy access to difficult posterior areas.
313C Bracket removal Pliers(Curved 90°)
Item No.: 004-313C
Usage: Bracket remover pliers(curved 90°),For removing all bonded attachment .May be used mesial-distal (horizontal) or incisal-gingival (vertical) in anterior areas.Angled perfectly for easy access to difficult posterior areas.
315/315G Ring to dismantle(tipped) Pliers
Item No.: 004-315(Head not inlaid with cemented carbide)/315G(Head inlaid with cemented carbide)
Usage: With the clamp and tooth surface as the fulcrum, the long and narrow wedge beak was used to remove the ring in the posterior tooth region. (It can also be used to remove attachments such as brackets that are directly attached to teeth.)
316/316G Crimpable hook placement Pliers
Item No.: 004-316(Head not inlaid with cemented carbide)/316G(Head inlaid with cemented carbide)
Usage: Used for locking free traction | hook to a certain position of the bow wire, locking operation is easy and labor saving.
317/317G Lingual filament cutting(tipped) Pliers
Item No.: 004-317(Head not inlaid with cemented carbide)/317G(Head inlaid with cemented carbide)
Usage: Elbow, mainly for tongue side. Used for cutting soft ligature wire or rubber band. Maximum cutting diameter 0.41mm(do not cut hard wire).
318/318G Thin end Winn forceps(tipped) Pliers
Item No.: 004-318(Head not inlaid with cemented carbide)/318G(Head inlaid with cemented carbide)
Usage: Small elbow, mouth with teeth. It is used to clamp the bow wire into the buccal tube, uncap the buccal tube and bend the end of the bow wire behind the buccal tube.
319/319G Adhesive removal(tipped) Pliers
Item No.: 004-319(Head not inlaid with cemented carbide)/319G(Head inlaid with cemented carbide)
Usage: Used to remove orthodontic adhesives from tooth surfaces without damaging tooth enamel. The cutting edge of the tool bar can be adjusted by spraying water on the grinding wheel to keep sharp.
320 Nance ring forming Pliers
Item No.: 004-320
Usage: Precision rings can be bent in four lengths -3/4/5/6mm. The base recess helps to close the ring ring, serrated, with a bow capacity of 022/56mm.
Disinfection Method
① Regular disinfection operation mode, first of all: disinfectant immersion, generally the use of multi-enzyme cleaning solution, depending on the degree of contamination of the instrument, heavy pollution (refers to the residual blood stains on the surface after use, and then no immediate immersion disinfection, blood stains and stains dry solid) in the case of disinfectant ratio 1: 100, soak for 15 to 30 minutes, light contamination (refers to the use of the surface of the blood is not dry solid, and then immediately disinfected) in the case of disinfectant ratio 1: 300, soak for 3-5 minutes, after soaking, clean with water, and then drain or dry, so that there is no moisture residue on the surface of the instrument, and then vacuum into the sterilization bag, put into the disinfection cabinet disinfection, generally using 134° three times chlorine vacuum disinfection.
②The procedure of instrument cleaning and disinfection is disinfection, cleaning, drying and sterilization. Because chemical disinfection has a certain corrosive effect on metals, physical disinfection methods are usually used: such as boiling, high pressure steam, dry heat, ultraviolet light, microwave, etc. Autoclave or dry heat method is the best. Among them, boiling, steam and other disinfection with water must go through the drying and drying process. It can not only ensure that the equipment gills and other parts are eroded by water for a long time, but also avoid 2 times of pollution.
Manufacturer | TREE |
---|---|
Products Category | Dental Forceps And Pliers |
Package Size | 7.5*2*22cm |
Package Gross Weight | 0.3kg |
Warranty
1. All the items at TREEDENTAL store are covered with a warranty. The warranty period is indicated in each item's description.
2. Warranty covers a replacement or repair of the faulty item. Contact us immediately for any issue that might happen to our product within the warranty period which is not man-made. You simply need to fill in the TREEDENTAL International Warranty Form here.
3. Within the warranty period, TREEDENTAL store will be responsible for covering the fee of the new spare parts and their shipping cost into your destination. If the faulty item needs to be sent back to our store for checking and repair, then we will cover the fee of shipping it back to our store. Upon its arrival to our store, we will cover the fee of the repair and ship it back to your doorstep for free also.
4. If your purchased item is out of the warranty period, then you can report the issue to us into [email protected] and our technical support team will issue you a report for the repair fee based on the kind of the fault.
5. Replacement: In case the product received comes with manufacturing defects, the buyers are entitled to request a product replacement within 7 days of receiving the item. To request a replacement, the buyers are required to provide photographic as well as video evidence of the product’s manufacturing defects which can be sent to our email: [email protected]. If the case is deemed valid, then we will cover the related cost to deliver a replacement.
The price displaying on website is factory price only, not including any shipping cost, your country’s import tax, customs clearance fee and insurance.
Shipping Cost
We can ship out the goods to you by three ways: Express ( DHL/UPS/FeDex/EMS), Air Shipping or Sea Shipping.
Express is the better way for order which the weight is under 10KG, it normally takes 4-7 days for delivery and delivery to your door directly.
Air Shipping is a good way for heavy order more than 100kg if you need the order urgently. It normally takes 7-10 days for delivery. But you need to do the customs clearance at your airport and pick the goods up there.
Sea Shipping is the lowest-cost way for big order, such as dental chair/dental unit order. It normally takes 30-60 days for delivery. But you need to do the customs clearance at your seaport and pick the goods up there.
The shipping cost which we charge you when you do the Checkout on our website is just for the Express shipping cost, if you want to use a cheaper shipping way, such as Sea Shipping, you need to contact us for the quote.
For the Air Shipping and Sea Shipping, if you don’t want to take the trouble to do the customs clearance and just want goods delivery to your door, we also can do that for you in additional charge.
Import Tax
Different country will have different import tax rate for different items, some country even 0 import tax for dental equipment. So if you want to know the exact import tax rate of the products, you need to inquire your customs department. Our price is not including any import tax, you need to pay it to your customs when the package arrive your country. But you can inform us to make a low value shipping invoice for you to avoid high import tax.
Shipping Insurance
Shipping insurance covers any damage or missing for your order during the transportation, so we highly recommend you to buy it for your large amount order. The insurance premium are as follows:
a.For Express/Air Shipping/Sea Shipping, the insurance premium= the sum insured*1.1*0.0008, minimum insurance premium for each bill is USD 30.
b.For Air Shipping or Sea Shipping with door to door delivery service, the insurance premium= the sum insured*1.1*0.0013, minimum insurance premium for each bill is USD 30.
c.Deductible: USD300 or 0.5% of the sum insured of the whole consignment, whichever is higher.
If you want to buy the shipping insurance for your order, you can buy it together with your order here: Cargo Transportation Insurance,PICC
Let’s take an example for these three different shipping ways (Just for reference):
One set of R7 dental chair shipped to Toronto, Canada.
Package Size: 147*110*153CM
Package Gross Weight:285KG
The value on shipping invoice: USD$4980
Shipping Ways |
Shipping Cost You Paid to Treedental (USD$) |
import tax (USD$)(For Canada, no duty but 5% GST) |
customs clearance fee(USD$) |
Delivery charge from airport/seaport to your door(USD$) |
Insurance(USD$) |
Total(USD$) |
Express (DHL/UPS/FeDex/EMS) |
3630 | 250 | 0 | 0 | 30 | 3910 |
Air Shipping | 2020 | 250 | 193 | 230 | 30 | 2723 |
Sea Shipping | 500 | 250 | 193 | 230 | 30 | 1203 |
1 set and 5 stes of R7 dental chair shipped to New York, United States.
Package Size: 147*110*153CM/SET
Package Gross Weight:285KG/SET
The value on shipping invoice: USD$4980/SET
Shipping Ways |
Shipping Cost You Paid to Treedental (USD$) |
import tax (USD$) |
Custom Duty(includ ISF)(USD$) |
Seaport Local Charge (USD$) |
Warehouse fee (USD$) |
Delivery charge from airport/ seaport to your door (USD$) |
Customs Clearance Fee (USD$) |
Total (USD$) |
Express (DHL/UPS/FeDex/EMS) 1 set |
3180 (From factory to your door) | 50 | 0 | 0 | 0 | 0 | 0 | 3230 |
Express (DHL/UPS/FeDex/EMS) 5 sets |
15900 (From factory to your door) | 250 | 0 | 0 | 0 | 0 | 0 | 16150 |
Air Shipping 1 set | 2310 (From factory to your airport) | 50 | 0 | 0 | 0 | 0 | 0 | 2360 |
Air Shipping 5 sets | 11550 (From factory to your airport) | 250 | 0 | 0 | 0 | 0 | 0 | 11800 |
Sea Shipping 1 set | 450 (From factory to your seaport) | 50 | 185 | 300 | 415 | 450 | 125 | 1925 |
Sea Shipping 5 sets | 545 (From factory to your seaport) | 250 | 260 | 715 | 535 | 900 | 125 | 3330 |